NuMaker-PFM-M2351 UART1 Programming
Posted: 16 May 2019, 16:57
Hi,
I am trying to print "hello world" using UART1. Pins used for UART1 are PB.6(Rx) and PB7(Tx).But when i open a terminal to view the output there is nothing printed on the serial terminal. Baud rate used is 115200.
I have developed code as follows in main.c:
void SYS_Init(void)
{
/* Enable PLL */
CLK->PLLCTL = CLK_PLLCTL_128MHz_HIRC;
/* Waiting for PLL stable */
while((CLK->STATUS & CLK_STATUS_PLLSTB_Msk) == 0);
/* Set HCLK divider to 2 */
CLK->CLKDIV0 = (CLK->CLKDIV0 & (~CLK_CLKDIV0_HCLKDIV_Msk)) | 1;
/* Switch HCLK clock source to PLL */
CLK->CLKSEL0 = (CLK->CLKSEL0 & (~CLK_CLKSEL0_HCLKSEL_Msk)) | CLK_CLKSEL0_HCLKSEL_PLL;
/* Select IP clock source */
CLK->CLKSEL1 = CLK_CLKSEL1_UART0SEL_HIRC;
/* Enable IP clock */
CLK->APBCLK0 |= CLK_APBCLK0_UART0CKEN_Msk;
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate PllClock, SystemCoreClock and CycylesPerUs automatically. */
//SystemCoreClockUpdate();
PllClock = 128000000; // PLL
SystemCoreClock = 128000000 / 2; // HCLK
CyclesPerUs = 128000000 / 1000000; // For SYS_SysTickDelay()
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set multi-function pins for UART0 RXD and TXD */
//SYS->GPB_MFPH = (SYS->GPB_MFPH & (~(UART0_RXD_PB12_Msk | UART0_TXD_PB13_Msk))) | UART0_RXD_PB12 | UART0_TXD_PB13;
SYS->GPB_MFPH = (SYS->GPB_MFPH & (~(UART1_RXD_PB6_Msk | UART1_TXD_PB7_Msk))) | UART1_RXD_PB6 | UART1_TXD_PB7;
}
void UART1_Init()
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init UART1 */
/*---------------------------------------------------------------------------------------------------------*/
UART1->LINE = UART_PARITY_NONE | UART_STOP_BIT_1 | UART_WORD_LEN_8;
UART1->BAUD = UART_BAUD_MODE2 | UART_BAUD_MODE2_DIVIDER(__HIRC, 115200);
}
int main()
{
int32_t i;
SYS_UnlockReg();
SYS_Init();
UART1_Init();
UART_Open(UART1,115200);
UART_Write(UART1,(uint8_t *)"Hello\n\r",7);
UART_Close(UART1);
}
Any link for guiding through the same would be helpful.
I am trying to print "hello world" using UART1. Pins used for UART1 are PB.6(Rx) and PB7(Tx).But when i open a terminal to view the output there is nothing printed on the serial terminal. Baud rate used is 115200.
I have developed code as follows in main.c:
void SYS_Init(void)
{
/* Enable PLL */
CLK->PLLCTL = CLK_PLLCTL_128MHz_HIRC;
/* Waiting for PLL stable */
while((CLK->STATUS & CLK_STATUS_PLLSTB_Msk) == 0);
/* Set HCLK divider to 2 */
CLK->CLKDIV0 = (CLK->CLKDIV0 & (~CLK_CLKDIV0_HCLKDIV_Msk)) | 1;
/* Switch HCLK clock source to PLL */
CLK->CLKSEL0 = (CLK->CLKSEL0 & (~CLK_CLKSEL0_HCLKSEL_Msk)) | CLK_CLKSEL0_HCLKSEL_PLL;
/* Select IP clock source */
CLK->CLKSEL1 = CLK_CLKSEL1_UART0SEL_HIRC;
/* Enable IP clock */
CLK->APBCLK0 |= CLK_APBCLK0_UART0CKEN_Msk;
/* Update System Core Clock */
/* User can use SystemCoreClockUpdate() to calculate PllClock, SystemCoreClock and CycylesPerUs automatically. */
//SystemCoreClockUpdate();
PllClock = 128000000; // PLL
SystemCoreClock = 128000000 / 2; // HCLK
CyclesPerUs = 128000000 / 1000000; // For SYS_SysTickDelay()
/*---------------------------------------------------------------------------------------------------------*/
/* Init I/O Multi-function */
/*---------------------------------------------------------------------------------------------------------*/
/* Set multi-function pins for UART0 RXD and TXD */
//SYS->GPB_MFPH = (SYS->GPB_MFPH & (~(UART0_RXD_PB12_Msk | UART0_TXD_PB13_Msk))) | UART0_RXD_PB12 | UART0_TXD_PB13;
SYS->GPB_MFPH = (SYS->GPB_MFPH & (~(UART1_RXD_PB6_Msk | UART1_TXD_PB7_Msk))) | UART1_RXD_PB6 | UART1_TXD_PB7;
}
void UART1_Init()
{
/*---------------------------------------------------------------------------------------------------------*/
/* Init UART1 */
/*---------------------------------------------------------------------------------------------------------*/
UART1->LINE = UART_PARITY_NONE | UART_STOP_BIT_1 | UART_WORD_LEN_8;
UART1->BAUD = UART_BAUD_MODE2 | UART_BAUD_MODE2_DIVIDER(__HIRC, 115200);
}
int main()
{
int32_t i;
SYS_UnlockReg();
SYS_Init();
UART1_Init();
UART_Open(UART1,115200);
UART_Write(UART1,(uint8_t *)"Hello\n\r",7);
UART_Close(UART1);
}
Any link for guiding through the same would be helpful.