Search found 311 matches
- 20 Feb 2023, 11:55
- Forum: Example Code
- Topic: [MS51] Adjusting PWM Duty Cycle Based on ADC Input Voltage
- Replies: 0
- Views: 15067
[MS51] Adjusting PWM Duty Cycle Based on ADC Input Voltage
Application: This example code uses MS51 PWM to output 10 kHz waveform with 0~100% duty cycle according to 0~3V ADC input voltage. BSP Version: MS51_Series_BSP_Keil_V1.00.004 Hardware: NuTiny-MS51DA V1.1 This example code uses MS51 PWM to output 10 kHz waveform with 0~100% duty cycle according to 0...
- 04 Jan 2023, 11:47
- Forum: Example Code
- Topic: [M032] Implementing USB Disk and FatFs function
- Replies: 0
- Views: 15961
[M032] Implementing USB Disk and FatFs function
Application: This example code uses the M032 series microcontroller (MCU) to implement USB Disk and FatFs function. BSP Version: M031 Series BSP CMSIS V3.05.000 Hardware: NuMaker-M032LD V1.1 This example code uses the M032 series microcontroller (MCU) to run USB mass storage functions and FatFs fil...
- 23 Dec 2022, 10:27
- Forum: Example Code
- Topic: [M480] CAN Bus-Off Recovery Mechanism
- Replies: 0
- Views: 7674
[M480] CAN Bus-Off Recovery Mechanism
Application: This example is an application code for CAN bus, which describes how to recover and let a device re-enter the bus for packet transmission and reception when a bus off occurs at the device node. BSP Version: M480 Series BSP CMSIS V3.05.003 Hardware: NuMaker-PFM-M487 V3.0 This example is...
- 20 Dec 2022, 16:15
- Forum: Example Code
- Topic: [M258] Completing COM/SEG LCD Project with NuTool-LCDView
- Replies: 0
- Views: 7583
[M258] Completing COM/SEG LCD Project with NuTool-LCDView
Application: This example code uses NuMaker-M258KG as an example to show how to complete a COM/SEG LCD project using NuTool-LCDView. BSP Version: M251_M252_M254_M256_M258_Series_BSP_CMSIS_V3.02.003 Hardware: NuMaker-M258KG V1.1 NuTool-LCDView is a powerful tool that can generate LCD configuration c...
- 15 Dec 2022, 14:09
- Forum: Example Code
- Topic: [M031] Data Transfer between SPI and 4 UARTs
- Replies: 0
- Views: 7039
[M031] Data Transfer between SPI and 4 UARTs
Application: This example code is used for the M031 series microcontroller (MCU) to transfer data between SPI and 4 UARTs. BSP Version: M031_Series_BSP_CMSIS_V3.05.000 Hardware: NuMaker-M031KI V1.0, NuMaker-M031SE V1.1 This example code is used for the M031 series microcontroller (MCU) to send and ...
- 15 Dec 2022, 14:04
- Forum: Example Code
- Topic: [M031] Using Bootloader to Upgrade APROM through BLE Module
- Replies: 0
- Views: 6791
[M031] Using Bootloader to Upgrade APROM through BLE Module
Application: This example code uses ISP_UART bootloader program in LDROM with IAP mode function to upgrade firmware in APROM through ESP32 BLE module. BSP Version: M031_Series_BSP_CMSIS_V3.05.000 Hardware: NuMaker-M032KI V1.0 This example code uses ISP_UART bootloader program of the M031 series mic...
- 05 Dec 2022, 14:17
- Forum: Example Code
- Topic: [M480] ISP Firmware Update and Restore
- Replies: 0
- Views: 4404
[M480] ISP Firmware Update and Restore
Application: This LDROM sample code divides APROM into run part and backup part. To restore the firmware in APROM, two parts are compared and updated after power cycling. BSP Version: M480 Series BSP CMSIS V3.05.003 Hardware: NuMaker-PFM-M487 V3.0 This LDROM sample code supports APROM update via UA...
- 22 Nov 2022, 09:13
- Forum: Example Code
- Topic: [M031/M032] Emulation Touch Screen Controller
- Replies: 0
- Views: 5863
[M031/M032] Emulation Touch Screen Controller
Application: This sample code uses the M031/M032 series microcontroller (MCU) to read a touch screen signal and analyze the position of the finger touch. This document will describe how to configure the ADC to read the signal, and how to configure the SPI to transmit data to the host. BSP Version: ...
- 17 Nov 2022, 14:46
- Forum: Example Code
- Topic: [MA35D1] GPIO PWM and Capture Linux Module Driver
- Replies: 0
- Views: 4769
[MA35D1] GPIO PWM and Capture Linux Module Driver
Application: This sample code shows how to import GPIO PWM and GPIO Capture driver into the Linux kernel, realize PWM output and detect the change status of pins. BSP Version: Linux-5.10.x Hardware: NuMaker-IOT-MA35D1 V2.0 This sample code demonstrates how to simulate the PWM signal through the “GP...
- 09 Nov 2022, 14:29
- Forum: Example Code
- Topic: [M030G] Using I2C to Read NCT7712Y Thermal Sensor
- Replies: 0
- Views: 15099
[M030G] Using I2C to Read NCT7712Y Thermal Sensor
Application: This example code uses M030G I2C to read NCT7712Y thermal sensor. BSP Version: M030G_Series_BSP_CMSIS_V3.02.000 Hardware: NuMaker-M030GTD V1.2 Microcontrollers (MCUs) are widely used in different ambient temperatures. Nuvoton NuMicro® Cortex®–M0 M030G/M031G series MCUs are provided wit...